Corrugated metal roofs are adequate metal roofing materials, but standing seam metal is one of the best investments any Denver CO homeowner can make. While they're initially expensive, their pros definitely outweigh their initial cons. In addition, they can last as long as 50-100 years with effective maintenance and knowing the right way in installing standing seam metal roofs.
If you want to know why even the most reputable and capable Denver CO metal roofers highly recommend installing standing seam metal roofs, Cajun Home Improvements has an excellent list of benefits it provides. Learn more below.
The Undeniable Benefits of Using a Standing Seam Metal Roof
Why choose a standing seam metal roof over asphalt shingles or other roofing materials? Here are 10 big reasons to choose durable, long-lasting standing seam metal roofing:
1. Design choices. Today’s metal roofing comes in a wide array of colors and finish choices and can handle curves and shapes better than asphalt.
2. Onsite rolling. Standing seam metal roofing can be rolled onsite to create longer sheets that eliminate the need for ugly overlapping ends, allow for bigger runs that can’t be delivered over the road.
3. Interior acoustics. When combined with the right materials underneath, standing seam metal roofing can create a home that sounds solid inside – with no tinny pings or other negative sound impacts. (Continued)
Cost is one initial obstacle homeowners have to face before the actual difficulties of installing standing seam metal roofs on their own. It is no small investment -- standing seam metal can cost about $1,250 per square on materials alone. While you might find materials ranging from $800 per square, it might mean a small compromise on quality -- so always perform proper research before buying.
ImproveNet has a great article on standing seam metal roof costs. This is highly ideal if you're planning a budget to replace your old roof or install it as a part of your new residence. Read more about it below.
Total Standing Seam Metal Roof Cost
All metal roofing costs come down to materials and labor. If you hire a professional roofer, expect to pay between $800 and $1,250 per square. In other words, your total standing seam metal roof cost will range between $8.00 and $12.50 per square foot (One square covers 100sf).
The total cost can fluctuate based on the quality of materials, the experience of the contractor, the roof layout, your location and various other factors discussed below.
Standing Seam Roof Costs – Materials
While material will usually not make up a majority of your total metal roof cost, they do encompass a good percentage. Like any material, there are basic and superior metal roofs. Nonetheless, expect to pay between $400 and $650 ($4.00/sf to $6.50/sf) for standing seam metal roof panels. (Continued)
Standing Seam Roof Costs – Labor
At this point, you've decided firmly and have budgeted your money. Now, you can start installing standing seam metal roofs. If you have a good hand in performing DIY, then you can use instructions to install your brand new Denver CO roof. On the other hand, you can look through instructions online to see and observe what your hired contractors should do when they start installation procedures.
Old House Online has a great set of instructions to serve as your guide and reference. You can read all about it below.
Installing Standing Seam Metal Roofs: The Complete Guide
Begin with a clean roof deck. Strip off all old roofing and pull all old nails, making sure that the surface is scrupulously free of anything that can puncture or blemish the new roof. On simple houses and secondary roofs, steel-based standing seam roofing is often installed over spaced decking or skip sheathing—boards laid with gaps of 1½" or so—but all three commonly used materials work equally well over closed-board or plywood decking. The next step for roofers using steel or the alloy terne is to underlay them with red rosin paper; never use black roofing felt or tar paper with these metals, since the asphalt will corrode them. Copper manufacturers do recommend a roofing felt underlayment topped by rosin building paper to keep the saturated felt from bonding to the copper. In any event, before starting, you should install metal edging around the perimeter of the roof to support the ½" to 1" overhang of the sheet metal to discourage water from running back under the edge. Use standard, prefabricated steel drip edge for Terne II and galvanized steel; use copper locking strip for copper. Nail the edging every 10" along gable ends and edges—anywhere that water will run off. (Continued)
Remember, in installing standing seam metal roofs, you'll need an experienced roofer with decades of experience in doing so. At Roper Roofing, you only have the best roofers in Denver with the knowledge and skill to meet your deadlines. In addition, they're friendly and approachable too. Learn more about what we can do for you -- contact us today!
